Hi Q Telecom Inc.

Step-by Step Instructions for the Installation and Programming of the T-Lock with options: Allowed Memory, Call Timer, Built-in LD service

FACTORY SETTINGS:

The T-Lock is pre-programmed at the factory to prevent dialing outgoing calls that begin with "0", "1", prefix 976, 411, or any phone number with more than 10 digits. You can easily program the T-Lock to "allow" additional dialing of specifiedd telephone numbers, prefixes or area codes by following the programming step 4 below. You may also change the digit limit retriction to restrict local calls (step 5 below). The T-Lock always allows dialing 911. You may override the restrictions with your four digit personal code.

SAFETY INSTRUCTIONS:

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

    1. Read and understand all instructions.
    2. Follow all warnings and instructions marked on the product.
    3. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
    4. This product should be operated from the telephone line only.
    5. Never push objects of any kind into this product except a telephone line cord as other objects may touch dangerous voltage points that could result in risk of fire or electric shock. Never spill liquid of any kind on the product.
    6. Refer servicing to qualified service personnel under the following conditions:

      If liquid has been spilled into the product.
      If the product has been exposed to rain or water.
      If the product does not operate normally by following the operating instructions.
      If the product has been dropped.
      If the product exhibits a distinct change on performance.

    7. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightening.

    8. Do not use the telephone to report a gas leak in the vicinity of the leak.

INSTALATION INSTRUCTIONS:

Read and understand all the safety instructions and the terminology prior to start the installation. The key of the installation is to connect the T-Lock in series between the telephone line coming from your local phone company and your telephone(s). Do not install the T-Lock at the Telephone Network Interface (located outside your property). The T-Lock must be installed replacing the main outlet in your property. Identify and remove your existing main phone jack wall plate or surface mount jack. Identify the 2-wire pair at the existing jack (usually red & green or yellow & black) corresponding to the telephone line from your local telephone company. If you have multiple lines (not extensions), you need to order one T-Lock unit per telephone line.
HINT: If you have two or more cables connected to the main phone jack, you may need to break all the connections in order to identify the 2-wire pair corresponding to the telephone line from your local telephone company.

Note (1): Surface Mounted styles come with a screw which is used to connect one of the extension wires. This longer screw, when screwed, will drill a hole in the plastic base to fix the T-Lock box to a surface or wall.
Note (2): Connect your chosen 2-wire pair to the T-Lock on the raised screw terminals, which have slotted head screws (see Figure 1).

PROGRAMING:

All programable features can be done using the dialpad of any telephone unit connected to any of the terminals (e.g. the main or extension terminals) of the T-Lock.
These programing instructions apply to software version 102-XXX or 103-XXX (find version code on white label fixed to chip). For other versions, follow the instructions above replacing "10 xxxx" with "11 xxxx".

Programable Feature # 1: To Change your Personal Code

a. Dial 10+2222 (factory preset personal code).
b. Wait for dialtone
c. Dial 1040
d. Wait for dialtone
e. Enter XXXX (your new 4 digit personal code*).
f. You will hear a single beep.
g. Hang up

* Please prevet using security codes that start with "10". Also, if there is a number you dial that begins with "10" be sure your new personal code is not the same as the first four digits of that number. We strongly recommend that you WRITE DOWN your new personal code and place it where you can find it if you happen to forget the code. There is no way to recover from a lost personal code except to return your T-Lock to the factory for a complete reset (see instructions below).

Programable Feature # 2: To Bypass the Restrictions

a. Dial 10+ xxxx (your personal code)
b. Wait for dialtone
c. Hang up
Now the unit is ready to dial any number without restriction
(Except those that begin with "10". To dial a number that begins with"10" see the next step)

2.1 To Bypass the Restrictions for a Number Beginning with "10":
For software version 102-XXX or 103-XXX (find version code on white label fixed to chip):

Dial 10+ xxxx (your personal code). Wait for a dial tone. Dial 1093 and wait for a dial tone. You may now dial any local or long distance number or any sequence of digits you may need for telephone pagers, telephone bank transactions or the like. When you hang up full restrictions will be automatically restored.

Now you may now dial any local or long distance number or any sequence of digits you may need for telephone pagers, telephone bank transactions or the like. When you hang up full restrictions will be automatically restored.

Programable Feature # 3: To Temporarily Disable all Restrictions (Permit All Outgoing Calls)

a. Dial 10+ xxxx (your personal code)
b. Wait for dialtone
c. Dial 1057 and you will hear a single beep
d. Wait for a dial tone, and then hang up
The telephone may now be dialed without restriction.

3.1 To Re-establish Restrictions and Programming:
a. Dial 10+ xxxx your personal code.
b. Wait for dialtone
c. Dial 1062 and you will hear a single beep.
d. Wait for a dial tone, and then hang up.
All call restrictions and previous programming are restored.

Programable Feature # 4: Program to Permit Certain Calls (in the "Allowed" Memory)

a. Dial 10+ xxxx your personal code
b. Wait for dialtone
c. Dial 1034
d. Wait for dialtone
e. Enter any telephone number, prefix or area code you want to allow
f. Press the # key (or wait 4 seconds)
g. A single beep will confirm that the number has been accepted into memory
h. Hang up
- Repeat steps e - g for all additional number you want to allow.

Tip (1): You may permit all numbers in an area code or prefix by entering just the area code or prefix or an area code and prefix to be allowed.
Tip (2): It is not necessary to enter your personal code for each number you wish to allow. After each entry you will hear a single beep. Wait for a new dial tone and enter the next number to be allowed.
Tip (3): When you have entered all the number you wish to allow simply hang up. When the memory is full you will hear two beeps instead of a single one. No more numbers may then be entered.
Tip (4): You can enter as many numbers, prefixes or area codes up to 200 digits (maximim capacity of this memory space). Also, you need you keep in mind that the "#" counts as a digit.

Programable Feature # 5: To Change the Digit Limit Restriction

a. Dial 10+ xxxx your personal code
b. Wait for dialtone
c. Dial 1076 and wait for a dial tone
d. Enter the new two digit limit restriction (00 through 99)
e. Wait to hear a single beep
f. Hang up

Tip (1): The factory default is 10 digits. If you enter 00 no outgoing calls will be allowed. If you enter 99 there will be no digit limit.
Tip (2): If you wish to block all local calls, we suggest you change the digit limit restriction to 02. This will block all calls with 2+ digits, except thos that are programmed in the allowed memory (check 4).

Programable Feature # 6: To Set the Optional Call Timer (Optional)

a. Dial 10+ xxxx your personal code
b. Wait for dialtone
c. Dial 1089 and wait for dialtone
d. Enter in a two digit number (00 through 99 minutes) that represents the allowed number of minutes
e. Hang up

Tip: This will be the number of minutes that any call may last. If you enter 00 the call timer will be disabled. The call time effects any outgoing or incoming call even if the number is in the memory of allowed phone numbers. The call timer will beep once at 30 seconds remaining and beep twice at 15 seconds remaining. At 0 seconds the call will be cut off. To override the timer for a single call, wait 40 seconds after dialing or answering your call and enter your personal code.

Programable Feature # 7. To Clear the T-Lock Memory of Allowed Number and Restore Factory Defaults

Dial 10+ xxxx your personal code. Wait for a dial tone. Dial 1021. You will hear a single beep. Wait for a dial tone and hang up. The memory is cleared of all programmed numbers and all factory defaults are reset except your personal code. Defatul settings are: Digit limit = 10, Call Timer = OFF, Factory Restrictions = ON (blocking all 0+, 1+, 411, 976 outbound calls).

WARRANTY & REPAIR SERVICE:

Hi Q TeleCOM Inc. warrants its products to be free of defects of material and workmanship for a period of one (1) year from the date of shipment. All items to be repaired under warranty are to be sent, together with the original sales slip, transportation prepaid to:
HiQ TeleCom Inc.
8004 NW 154 ST # 401
Miami, FL 33016
Product will be repaired or replaced at HQT’s option and returned "NO COST" provided in HQT’s opinion the item(s) have not been improperly installed, damaged or altered without authorization.

If you loose or forget your Owner's security code:
If you loose or forget your owner's security code (default as 2222), you will need to send the unit back to the factory (to the address above) for a factory reset. Please add a $20 check to cover the handling & shipping costs.

See Frequently Asked Questions and Programming Examples
For additional information, visit http://hqtelecom.com

1995 - 2006 Hi Q Telecom Inc. All rights reserved